Hi guys, i've got a frustrating problem with my irons. If i concentrate on a full release and horizontal hinge i tend to pick the ball cleanly even with wedges and don't take a divot.
If i concentrate on hitting down more then i hit a lot of shanks as my hands tend to lock up and do not square the face.
I've been really trying with chip shots etc to keep the hands ahead, so much so that it blocks the hinge action.
Anyone else had the same problems and any remedies?
Hit the practice bunker. Line in the sand. Divots on the forward side of the line. Make sure you can do it without your upper body lunging forward. At least, that's my trouble.
Hi guys, i've got a frustrating problem with my irons. If i concentrate on a full release and horizontal hinge i tend to pick the ball cleanly even with wedges and don't take a divot.
If i concentrate on hitting down more then i hit a lot of shanks as my hands tend to lock up and do not square the face.
I've been really trying with chip shots etc to keep the hands ahead, so much so that it blocks the hinge action.
Anyone else had the same problems and any remedies?
Cheers
if the ball flight and results are acceptable, why is this bad?
if the ball flight and results are acceptable, why is this bad?
-hcw
Three dimensional impact (down, out, forward) is desired to get maximum compression which results in more power and a more controllable trajectory.
bergsey: This issue could be as simple as ball position. Ensure you are setting up with your low point (left shoulder) ahead of the ball. Another cause could be that you are not maintaining a flat left wrist at impact. I've seen guys "flip" at the ball which will scoop it instead of hitting down properly and taking a divot.
Make sure your set up is correct. Then start by hitting some short pitch shots where you finish with both arms straight and a follow though no further than waist high. Concentrate on down, out, and forward. You should be taking divots with this procedure. The divots should be in front of the ball. See 12-5-2 Aquired Motion.
Where is your ball position in relation to your left shoulder joint?
Hi there, i swing from impact fix. So for wedges the ball is around mid point in my stance with my hands over my left foot.
If i concentrate on a divot in front of the ball - e.g. the line in the sand drill i can do it. My problem is when i do this i lose the clubface control and tend to drag the hosel in first. So it tends to a choice in my mind between shank with divot or pick clean
Chips and small shots aren't a problem - this is more for half swings and beyond
No Diviots with the Irons!
Well I have heard some wonderful suggestions but I recomend you apply 3-F-5. You mentioned that when you try to hit DOWN which you MUST do you shank the ball. Set your radius correctly ie sole the club towards the TOE. Surely if we are driving DOWNWARD OUTWARD & FORWARD WHICH WE MUST, a shank is likely if one soles the club towards the center.
Now you are driving down on the ball and providing you have followed 3-F-5 correctly your divot should come from impact point plane line to the low point plane line. www.blackburngolf.com
Set your radius correctly ie sole the club towards the TOE.
Thanks, that might well be it as i'm currently setting up at impact fix (address?) with the club soled at the sweetspot. I'll give that a go! (at worst coming off the toe has to be better than off the hosel...
Also, there are only 2 main reasons why people shank the ball in my opinion:
1) You let the face open in the backswing like a swinger and then you try and "hit" the ball through impact. Because you let it open and are hitting, nothing has closed the face and wala...SHANK
2) You are too close to the ball at address. As you make your backswing your weight will move to your heels and on the downswing back onto your toes bringing everything "closer" to the ball and thus bring the hosel into ball.
__________________
I'm not a TGM or PGA certified Pro, but I did stay at a Holiday Inn Express last night
Linear Mode
