That question covers a lot of different topics. I think much of this can be researched best by using the search function. Here are some suggestions for key words :
-"hinge action"
- "swivel"
-"release triggers"
-"geometry of the circle"
In regard to hitting it fat; I would say that with a Level Left Wrist at Fix, Extensor Action and a steady left shoulder (achieved via a steady non bobbing or swaying Head) hitting it fat should be near impossible.
To draw a perfect circle you must have a fixed center and a properly extended radius. Like a string line from nail to pencil used by a carpenter to draw a curve, the left arm and club (Primary Lever Assembly, the radius) must be held taut via extensor action at fix to properly measure the correct distance from the Left Shoulder (center) to the ball. Once measured, nail the Left Shoulder or the Head into position.
If the Left Wrist is cocked slightly at Fix (slack in the string, bad measurement) and then stretched to a fuller extension dynamically during the swing OR if your Left Shoulder moves closer to the ball during the swing (not nailed).......you'll hit it fat. If you measure properly and nail it down but then let your string (Primary Lever Assembly) go slack during the swing you'll hit it thin. Most people encountering this latter situation develop a head bob or lowering as a compensation. This works to the extent that they can maintain a consistent radius with an un stretched Primary Lever Assembly.........which is hightly doubtful........... for that reason the carpenter uses a taut string line and so should we.
The added benefit to Extensor Action is increased velocity via a wider arc, increased structure and mass which adds to the blow to the ball. Velocity and mass, every golfer has to like that.
That question covers a lot of different topics. I think much of this can be researched best by using the search function. Here are some suggestions for key words :
-"hinge action"
- "swivel"
-"release triggers"
-"geometry of the circle"
In regard to hitting it fat; I would say that with a Level Left Wrist at Fix, Extensor Action and a steady left shoulder (achieved via a steady non bobbing or swaying Head) hitting it fat should be near impossible.
To draw a perfect circle you must have a fixed center. Like a string line from nail to pencil used by a carpenter to draw a curve or radius, the left arm and club (Primary Lever Assembly) must be held taut via extensor action at fix to properly measure the correct distance from the Left Shoulder (center) to the ball. Once measured nail the Left Shoulder or the Head into position.
If the Left Wrist is cocked slightly at Fix (bad measurement) and then stretched to a fuller extension dynamically during the swing OR if your Left Shoulder moves closer to the ball during the swing (not nailed).......you'll hit it fat. If you measure properly and nail it down but then let your string (Primary Lever Assembly) go slack during the swing you'll hit it thin. Most people encountering this latter situation develop a head bob or lowering as a compensation. This works to the extent that they can maintain a consistent radius with an un stretched Primary Lever Assembly.........which is hightly doubtful........... for that reason the carpenter uses a taut string line and so should we.
The added benefit to Extensor Action is increased velocity via a wider arc, increased structure and mass which adds to the blow to the ball. Velocity and mass, every golfer has to like that.
Hope this helps.
Extensor action is important to solid sweet spot impact if done correctly. Many golfers will apply just the push of the right arm without a slight pull of the left arm and this can change the radius of the left arm. The results are fat shots. Make sure you have opposite pull of the left arm to the pushing right arm to maintain the same radius of the left arm when applying extensor action. Fat shots will be a thing of the past.
Extensor action is important to solid sweet spot impact if done correctly. Many golfers will apply just the push of the right arm without a slight pull of the left arm and this can change the radius of the left arm. The results are fat shots. Make sure you have opposite pull of the left arm to the pushing right arm to maintain the same radius of the left arm when applying extensor action. Fat shots will be a thing of the past.
Bold by Andy R
I can't remember reading or hearing Mr Kelly say anything about the "opposite pull of the left arm" with regard to Extensor Action. I'd love to hear what he had to say about that, though. Can you let me know where you heard or read that? Thanks in advance.
I can't remember reading or hearing Mr Kelly say anything about the "opposite pull of the left arm" with regard to Extensor Action. I'd love to hear what he had to say about that, though. Can you let me know where you heard or read that? Thanks in advance.
I did not hear it from any one. I have been teaching it for 20 years. Give it a try. It works.
I did not hear it from any one. I have been teaching it for 20 years. Give it a try. It works.
i developpend shank city trying this, but its probably my fault, coz as my focus changed doing this, the swing thoughts change so i probably started manipulating the club instead of letting law work for me.
Works great for me. The left arm pull is very slight, just enough to keep me from pulling my arm out of socket. Great structure and a little more right arm bend.
That question covers a lot of different topics. I think much of this can be researched best by using the search function. Here are some suggestions for key words :
-"hinge action"
- "swivel"
-"release triggers"
-"geometry of the circle"
In regard to hitting it fat; I would say that with a Level Left Wrist at Fix, Extensor Action and a steady left shoulder (achieved via a steady non bobbing or swaying Head) hitting it fat should be near impossible.
To draw a perfect circle you must have a fixed center and a properly extended radius. Like a string line from nail to pencil used by a carpenter to draw a curve, the left arm and club (Primary Lever Assembly, the radius) must be held taut via extensor action at fix to properly measure the correct distance from the Left Shoulder (center) to the ball. Once measured, nail the Left Shoulder or the Head into position.
If the Left Wrist is cocked slightly at Fix (slack in the string, bad measurement) and then stretched to a fuller extension dynamically during the swing OR if your Left Shoulder moves closer to the ball during the swing (not nailed).......you'll hit it fat. If you measure properly and nail it down but then let your string (Primary Lever Assembly) go slack during the swing you'll hit it thin. Most people encountering this latter situation develop a head bob or lowering as a compensation. This works to the extent that they can maintain a consistent radius with an un stretched Primary Lever Assembly.........which is hightly doubtful........... for that reason the carpenter uses a taut string line and so should we.
The added benefit to Extensor Action is increased velocity via a wider arc, increased structure and mass which adds to the blow to the ball. Velocity and mass, every golfer has to like that.
Hybrid Mode
